Combustible Dust Testing

Laboratory testing to quantify dust explosion and reactivity hazards

Safety Data Sheets

Develop critical safety data for inclusion in SDS documents

Gas and Vapor

Laboratory testing to quantify explosion hazards for vapor and gas mixtures

UN-DOT
Classification of hazardous materials subject to shipping and storage regulations
Hydrogen
Testing and consulting on the explosion risks associated with devices and processes which use or produce hydrogen
Safety Data Sheets

Develop critical safety data for inclusion in SDS documents

Thermal Stability

Safe storage or processing requires an understanding of the possible hazards associated with sensitivity to variations in temperature

Adiabatic Calorimetry
Data demonstrate the consequences of process upsets, such as failed equipment or improper procedures, and guide mitigation strategies including Emergency Relief System (ERS) design
Reaction Calorimetry
Data yield heat and gas removal requirements to control the desired process chemistry
Battery Safety

Testing to support safe design of batteries and electrical power backup facilities particularly to satisfy UL9540a ed.4

Safety Data Sheets

Develop critical safety data for inclusion in SDS documents

Cable Testing
Evaluate electrical cables to demonstrate reliability and identify defects or degradation
Equipment Qualification (EQ)
Testing and analysis to ensure that critical equipment will operate under adverse environmental conditions
Water Hammer
Analysis and testing to identify and prevent unwanted hydraulic pressure transients in process piping
Acoustic Vibration
Identify and eliminate potential sources of unwanted vibration in piping and structural systems
Gas & Air Intrusion
Analysis and testing to identify and prevent intrusion of gas or air in piping systems
ISO/IEC 17025:2017

Fauske & Associates fulfills the requirements of ISO/IEC 17025:2017 in the field of Testing

ISO 9001:2015
Fauske & Associates fulfills the requirements of ISO 9001:2015
Dust Hazards Analysis
Evaluate your process to identify combustible dust hazards and perform dust explosion testing
On-Site Risk Management
On-site safety studies can help identify explosibility and chemical reaction hazards so that appropriate testing, simulations, or calculations are identified to support safe scale up
DIERS Methodology
Design emergency pressure relief systems to mitigate the consequences of unwanted chemical reactivity and account for two-phase flow using the right tools and methods
Deflagrations (Dust/Vapor/Gas)

Properly size pressure relief vents to protect your processes from dust, vapor, and gas explosions

Effluent Handling

Pressure relief sizing is just the first step and it is critical to safely handle the effluent discharge from an overpressure event

FATE™ & Facility Modeling

FATE (Facility Flow, Aerosol, Thermal, and Explosion) is a flexible, fast-running code developed and maintained by Fauske and Associates under an ASME NQA-1 compliant QA program.

Mechanical, Piping, and Electrical
Engineering and testing to support safe plant operations and develop solutions to problems in heat transfer, fluid, flow, and electric power systems
Hydrogen Safety
Testing and consulting on the explosion risks associated with devices and processes which use or produce hydrogen
Thermal Hydraulics
Testing and analysis to ensure that critical equipment will operate under adverse environmental conditions
Nuclear Safety
Our Nuclear Services Group is recognized for comprehensive evaluations to help commercial nuclear power plants operate efficiently and stay compliant
Radioactive Waste
Safety analysis to underpin decomissioning process at facilities which have produced or used radioactive nuclear materials
Adiabatic Safety Calorimeters (ARSST and VSP2)

Low thermal inertial adiabatic calorimeters specially designed to provide directly scalable data that are critical to safe process design

Other Lab Equipment and Parts for the DSC/ARC/ARSST/VSP2 Calorimeters

Products and equipment for the process safety or process development laboratory

FERST

Software for emergency relief system design to ensure safe processing of reactive chemicals, including consideration of two-phase flow and runaway chemical reactions

FATE

Facility modeling software mechanistically tracks transport of heat, gasses, vapors, and aerosols for safety analysis of multi-room facilities

Blog

Our highly experienced team keeps you up-to-date on the latest process safety developments.

Process Safety Newsletter

Stay informed with our quarterly Process Safety Newsletters sharing topical articles and practical advice.

Resources

With over 40 years of industry expertise, we have a wealth of process safety knowledge to share.

Recent Posts

VSP2 – Everything You Need to Know About Setting Up Your Heater Assembly

Posted by Fauske & Associates on 06.11.19

By Elizabeth Raines, Chemical Engineer, Fauske & Associates, LLC

Introduction

Ensuring that the VSP2 heater assembly is setup properly is crucial to performing a successful test. While the heater and heater glands are reusable parts, testing their integrity prior to beginning a test and replacing any questionable parts will help to ensure success. Further, care should be taken to insulate the test cell and heater assembly inside of the containment vessel as well as possible. The heat loss of the assembly during the test will be a determining factor in the overall quality of the test data. This article and video discusses the proper electrical testing and insulating procedures for the heater assembly and provides some setup tips and tricks.

 

 

Heat Assembly Background

The VSP2 heater assembly is comprised of two separate heaters; the "Main" or "Auxiliary" heater (the "driver" heater used to raise the test cell temperature), and the "Guard" heater (used to maintain the adiabatic environment). The Auxiliary (test cell) heater has approximately three turns of heater wire over the lower quarter and base of the test cell. The nominal resistance of this heater element is 18 ohms. After inserting the test cell in the Auxiliary (Main) heater, a layer of insulation is wrapped around the cell. The Auxiliary heater has wires with male prongs that are shrink wrapped in yellow tape. This insulated cell assembly in turn fits inside the Guard heater assembly. The Guard heater consists of two separate, connected circuits; the larger comprising the bottom and walls, and the top comprising the lid. These are connected using the smaller male and female prongs (these are wrapped with red shrink tape while the Guard heater's other connectors are larger male prongs and the standard assembly uses green shrink tape along these fittings). The nominal resistance of the Guard heater assembly (both elements connected) is 58 ohms. A dual zone “Multizone” Guard heater divides the Guard heater into two zones. The lower zone (controlled by TC2, green tape) comprises the base and lower half of the Guard heater while the top zone (controlled by TC3, and now includes additional blue wrapped male prongs) comprises the upper half. The nominal resistance of the base zone is 29 ohms and of the top zone is 33 ohms. This video and article focuses on the standard heater assembly, but the procedure and principles apply to the Multizone heater assembly as well.

Auxiliary Heater and Guard Heater

Electrical Checks

Note, in the following pictures, the locations where the multimeter leads should make contact are identified by blue and red dots, respectively.

Heater

There are four primary checks to be performed to ensure your heater is in good working condition:

A. Verify that the resistance across the Auxiliary heater is approximately 18 ohms

- Turn your multimeter on and set to read resistance (might be shown with the Greek letter omega, Ω, or the word “ohms”)

- Connect each of the leads from the multimeter onto each male prong on the Auxiliary heater:

 

Connected leads from multimeter onto each male prong

 

- The resistance across these two locations should read approximately 18 ohms

B. Verify that the Auxiliary heater is not shorted out and that the resistance is > 10 Mega ohms

- Turn your multimeter on and set to read resistance

- Connect one of the leads from the multimeter to one of the Auxiliary heater male prongs and the other lead to a       part of the Auxiliary heater coil:

Connect one of the leads from the multimeter to one of the Auxiliary heater male prongs and the other lead to a part of the Auxiliary heater coil

 

- The resistance across these two locations should read a very large resistance indicating that the heater is not shorted to the foil (>10 Mega ohms)

C. Verify that the resistance across the Guard heater is approximately 58 ohms

- Turn your multimeter on and set to read resistance

- Connect the lid heater to the base and lower half heater by connecting the two red smaller female and male prong (the green dots in the photo below)

- Connect each of the leads from the multimeter onto each of the green Guard heater prongs:

Connect each of the leads from the multimeter onto each of the green Guard heater prongs

 

- The resistance across these two locations should read approximately 58 ohms

D. Verify that the Guard heater is not shorted out and that the resistance is > 10 Mega ohms

- Turn your multimeter on and set to read resistance

- Connect the lid heater to the base and lower half heater by connecting the two red smaller female and male prong

- Connect one of the leads from the multimeter to one of the Guard heater male prongs and the other lead to a part of the Guard heater coil:

Connect one of the leads from the multimeter to one of the Guard heater male prongs and the other lead to a part of the Guard heater coil

 

-  The resistance across these two locations should read a very large resistance indicating that the heater is not shorted out (>10 Mega ohms)

 

Heater Gland

There are four primary checks to be performed to ensure your heater gland is in good working condition:

A. Verify the heater gland continuity through the vessel

- Turn your multimeter on and set to read continuity (it might look this this symbolSymbol, otherwise set to resistance)

- Connect one of the multimeter leads into one of the female heater gland locations (on the interior of the vessel) and connect the other lead to the male prong on the exterior side of the vessel (touch the metal part on each side):

Connect one of the multimeter leads into one of the female heater gland locations (on the interior of the vessel) and connect the other lead to the male prong on the exterior side of the vessel (touch the metal part on each s

 

- When a complete path is reached, the multimeter will beep (and show a very small resistance of ~0.3-0.5 ohms). Only one pair of male/female parts should be detected as a complete path

- Swap pairs and test that the other wire is intact

- Repeat this procedure on the other set of wires

B. Verify the heater gland wires are not shorted to the vessel and that it is > 10 Mega ohms

 - Turn your multimeter on and set to read resistance

 - Connect one of the multimeter leads onto one of the male heater gland prongs and connect the other lead to the vessel:

Connect one of the multimeter leads onto one of the male heater gland prongs and connect the other lead to the vessel

- The resistance across these two locations should read a very large resistance indicating that the heater is not shorted to the vessel

- Repeat this procedure on the other set of wires

C. Plug the Auxiliary and Guard heaters into the heater gland and verify that the resistance across the Auxiliary heater is 18 ohms and the resistance across the Guard Heater is 58 ohms

- Turn your multimeter on and set to read resistance

- Connect each of the leads from the multimeter onto each male prong on the exterior heater gland that is connected to the Auxiliary heater:

Connect each of the leads from the multimeter onto each male prong on the exterior heater gland that is connected to the Auxiliary heater

 

- The resistance across these two locations should read approximately 18 ohms

Note, the heater glands consist of two black wires and two white wires. The two Auxiliary heater wires (yellow) should be connected to either two white or two black. The two Guard heater wires (green) should be connected to the other two wires not used for the Auxiliary heater. Then, on the exterior of the vessel, the resistance across the two male prongs should match the resistance of the heater that is connected to it.

- Connect each of the leads from the multimeter onto each male prong on the exterior heater gland that is connected to the Guard heater:

Connect each of the leads from the multimeter onto each male prong on the exterior heater gland that is connected to the Guard heater

 

- The resistance across these two locations should read approximately 58 ohms

D. Plug the Auxiliary and Guard heaters into the heater gland and verify that the heater assembly is not shorted out to the vessel and that the resistance is > 10 Mega ohms

- Turn your multimeter on and set to read resistance

- Connect one of the leads from the multimeter onto one of male prongs on the exterior heater gland and connect the other lead to the vessel:

Connect one of the leads from the multimeter onto one of male prongs on the exterior heater gland and connect the other lead to the vessel

 

- The resistance across these two locations should read a very large resistance (>10 Mega ohms)

- Repeat with the other prongs

 

Test Cell Installation

The recommended method of insulating and installing the VSP2 test cell is as follows:
Tip—lay out all the required materials before we begin wrapping the test cell to make the process as quick as possible.

  1. Place the test cell into the Auxiliary heater.

    Note, it is good practice to record the weight of the test cell before (for phi-factor calculations) and after (for measuring mass loss during the test) installing the required fittings.

  2. Wrap the test cell and test cell heater with 2 3/4" wide paper insulation. Use one full-length strip (24") followed by 1/4 of a strip (6"). Use masking tape to hold the insulation in place.

    Note, when wrapping the test cell with the paper insulation, it is helpful to tuck the starting end of the insulation strip underneath the vertical leads of the test cell heater. Subsequent wraps are on top of the test cell heater leads. This provides a snugger fit of the test cell in the insulation, minimizing the air gap between the test cell and the insulation. Elimination of the air gap prevents possible convective heat transfer and thereby tends to improve insulation performance particularly at high temperatures and pressures. Normally there is no problem seating the new test cell into the test cell heater, but a twisting motion is necessary for all-welded test cells that have a weld bead on the bottom lip.

    Tip—begin by using 3 ~2-3" pieces of masking tape to seal the seams of the paper insulation. Then use 5~6" pieces of tape to wrap the bottom of the test cell. This creates a smoother barrier that makes it easier to slide the test cell into the Guard heater.

    Note that the
    test cell should be insulated from the Guard heater on all sides – along the wall, top, and bottom with the same thickness insulation layer.

  3. Place a 1/2-thickness disk of Fiberfrax insulation (about 1/4" thick) inside the Guard heater can.

    Note that the insulation can irritate the respiratory tract or skin if it comes in contact with it so use caution and the proper PPE.

  4. Slide the wrapped test cell down into the Guard heater can.

    Tip—mark the thermocouples 1 for the sample thermocouple and 2 for the Guard heater (If using Multizone Multizone heater, mark 3 for the upper zone heater). This makes it clear on the proper connections when the test cell is installed in the containment vessel.

  5. Place a full thickness Fiberfrax disk on top of the test cell. Note, for the thermocouple or if a test cell with a vent is used, the disk on top of the test cell should be cut in half to make room for the different parts.

    Tip—it is helpful to have a separate pair of scissors for cutting tape and for cutting the Fiberfrax disks. Cutting the Fiberfrax disks dull the scissors making it difficult to cut tape overtime.

  6. Install the lid heater on top of the test cell assembly, crimping over the top edge of the Guard can if desired to hold the lid heater in a fixed position. A strip or two of white glass-cloth insulation tape can be used to help hold the lid heater securely on top of the assembly.

    Tip—it is helpful to align the test cell, Auxiliary heater, and Guard heater assembly so that the heater wires remain close to each other to make it easier to make the required connections.

  7. Place a large Fiberfrax disk on the containment vessel floor. Note, this current video shows the heater gland checks and the test cell insulation. A future video will walk through installing the test cell into the containment vessel and making the required connections.

  8. Install several large doughnuts (have a whole cut out from the middle for the test cell) of insulation in the vessel to just below where the fill lines connect.

  9. Slide the Guard heater/test cell assembly down into this nest.

  10. Connect the fill line(s) and Guard heater ground strap(s).
    Note, for the standard heater assembly, this can be accomplished by using a three way ground strap and connecting one of the lines to the fill line, and connecting to each of the red heater wires

  11. Tighten the nuts to the fill line and the pressure line.

    Note, if used, support, the 1/16" fill line when bending it to avoid a sharp bend in the tube. Also, ensure that the tube are aligned with the 1/16" or 1/8" bulkhead fitting by first rotating the nut counterclockwise until a click is heard. Then tighten the nut finger tight. Using a wrench tighten the nut an additional 1/8 of a turn.

  12. Continue installing doughnut segments (usually cut in two or three pieces so they can be fitted around obstacles).

  13. Use small Fiberfrax discs on top of the test cell assembly, cutting them in half or notching as needed to fit around thermocouples and fittings. Insulate up to the upper containment vessel wall penetration. The overall assembly is illustrated below.
The overall assembly 

Adiabatic calorimeter testing provides data for relief system design, safe scale-up of chemical processes, and changes to process recipes.  Safe process design requires knowledge of chemical reaction rates, character and energy release - all of which can be obtained from a low phi-factor adiabatic calorimeter such as the VSP2TM (Vent Sizing Package 2) or ARSSTTM (Advanced Reactive System Screening Tool). If you are interested in purchasing either the VSP2TM  or ARSSTTM check out our store by clicking below.

Visit Our Online Store

Topics: Process Safety, VSP2, Reactive Chemicals

cta-bg.jpg

Is My Dust Combustible?

A Flowchart To Help You Decide
Download Now